完善资料让更多小伙伴认识你,还能领取20积分哦, 立即完善>
我正在使用Cosmic 32k编译器版本4.3.6和STVD版本4.3.1用于带有ST8S208C芯片的项目。问题似乎是编译器。每当我打开中断时进行32位数学运算,我偶尔会看到结果中的损坏。编译器切换@svlreg应该解决这个问题,但显然没有。当我联系Cosmic时,他们说看到ST论坛是因为我们没有与他们达成付费支持协议。我在这里。我在这些论坛上搜索了有关这个问题的任何内容,但是已经很短了。我想知道是否有其他人遇到过这个问题。
#宇宙svlreg 以上来自于谷歌翻译 以下为原文 I'm using the Cosmic 32k compiler version 4.3.6 and STVD Version 4.3.1 for a project with an ST8S208C chip. The problem seems to be the compiler. Whenever I do 32 bit math while interrupts are on, I occasionally see corruption in the results. The compiler switch @svlreg is supposed to address this problem but it apparently does not. When I contacted Cosmic about this, they said to see the ST forums because we don't have a paid support agreement with them. So here I am. I searched these forums for anything concerning this problem but have come up short. I was wondering if anyone else has encountered this problem. #cosmic-svlreg |
|
相关推荐
1个回答
|
|
你好,
@svlreg将是第一个答案:确保在所有中断函数上使用它。 另一种可能性是您不保护中断的32位变量访问(在stm8上是非原子的)。 问候, 卢卡 以上来自于谷歌翻译 以下为原文 Hello, @svlreg would be the first answer: make sure you use it on all your interrupt functions. Another possibility is that you don't protect your 32 bit variable accesses (that are non atomic on the stm8) from interrupt. Regards, Luca |
|
|
|
只有小组成员才能发言,加入小组>>
stm32mp157的异核通信的rpmsg_sdb的m4固件和a7驱动该如何编写?
932 浏览 0 评论
stm32f103用freertos对一个采样率为1kHz的传感器,进行采样,数据出差
983 浏览 0 评论
请教:在使用UDE STK时,单片机使用SPC560D30L1,在配置文件怎么设置或选择?里面只有SPC560D40的选项
3150 浏览 1 评论
3414 浏览 1 评论
请问是否有通过UART连接的两个微处理器之间实现双向值交换的方法?
2006 浏览 1 评论
STM32H7打开DCache后,出现了串口接收信息为空的现象,是哪里出了问题?
165浏览 5评论
用NANO STM32F103RBT6的开发板烧录不了是哪里出了问题?
182浏览 5评论
205浏览 5评论
外部中断触发类型为双边沿触发,进入中断回调后有什么办法判断该边沿是上升沿还是下降沿?
250浏览 5评论
STM32L071CBT6低温环境下无法正常工作是什么原因引起的?
192浏览 5评论
小黑屋| 手机版| Archiver| 电子发烧友 ( 湘ICP备2023018690号 )
GMT+8, 2025-7-16 22:45 , Processed in 0.469124 second(s), Total 47, Slave 41 queries .
Powered by 电子发烧友网
© 2015 bbs.elecfans.com
关注我们的微信
下载发烧友APP
电子发烧友观察
版权所有 © 湖南华秋数字科技有限公司
电子发烧友 (电路图) 湘公网安备 43011202000918 号 电信与信息服务业务经营许可证:合字B2-20210191