[经验]

【全志T113-i】OK113i-S开发板CAN通信C代码测试

2024-1-19 10:00:51

2093 CAN

飞凌官方手册中关于CAN测试部分使用的是命令行进行的简单测试，实际开发过程中还是要使用C代码去操作CAN设备，本帖主要讲解怎么使用C代码对CAN设备进行读写的收发操作。
First of all ，先查看所有网卡信息，看看板上是否有CAN设备网络：
root@ok113i:/# ifconfig -acan0    Link encap:UNSPEC  HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00          NOARP  MTU:16  Metric:1       RX packets:0 errors:0 dropped:0 overruns:0 frame:0       TX packets:0 errors:0 dropped:0 overruns:0 carrier:0       collisions:0 txqueuelen:10          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)can1    Link encap:UNSPEC  HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00          NOARP  MTU:16  Metric:1       RX packets:0 errors:0 dropped:0 overruns:0 frame:0       TX packets:0 errors:0 dropped:0 overruns:0 carrier:0       collisions:0 txqueuelen:10          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)       Interrupt:1 eth0    Link encap:Ethernet  HWaddr BA:E9:F2:1C:9D:87          inet addr:192.168.0.232  Bcast:0.0.0.0  Mask:255.255.255.0       inet6 addr: fe80::b8e9:f2ff:fe1c:9d87/64 Scope:Link       UP BROADCAST RUNNING MULtiCAST  MTU:1500  Metric:1       RX packets:421 errors:0 dropped:14 overruns:0 frame:0       TX packets:9 errors:0 dropped:0 overruns:0 carrier:0       collisions:0 txqueuelen:1000          RX bytes:27272 (26.6 KiB)  TX bytes:726 (726.0 B)       Interrupt:39 ip6tnl0 Link encap:UNSPEC  HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00          NOARP  MTU:1452  Metric:1       RX packets:0 errors:0 dropped:0 overruns:0 frame:0       TX packets:0 errors:0 dropped:0 overruns:0 carrier:0       collisions:0 txqueuelen:1000          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)lo       Link encap:Local Loopback          inet addr:127.0.0.1  Mask:255.0.0.0       inet6 addr: ::1/128 Scope:Host       UP LOOPBACK RUNNING  MTU:65536  Metric:1       RX packets:0 errors:0 dropped:0 overruns:0 frame:0       TX packets:0 errors:0 dropped:0 overruns:0 carrier:0       collisions:0 txqueuelen:1000          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)sit0    Link encap:IPv6-in-IPv4          NOARP  MTU:1480  Metric:1       RX packets:0 errors:0 dropped:0 overruns:0 frame:0       TX packets:0 errors:0 dropped:0 overruns:0 carrier:0       collisions:0 txqueuelen:1000          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)wlan0    Link encap:Ethernet  HWaddr 2C:C3:E6:67:4D:3B          BROADCAST MULTICAST  MTU:1500  Metric:1       RX packets:0 errors:0 dropped:0 overruns:0 frame:0       TX packets:0 errors:0 dropped:0 overruns:0 carrier:0       collisions:0 txqueuelen:1000          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
1. CAN组网前的准备，设置CAN通信服务的通信速率。使用如下命令分别设置CAN0和CAN1的通信速率：
root@ok113i:/home/forlinx# ip link set can0 up type can bitrate 500000[ 4075.425084] IPv6: ADDRCONF(NETDEV_CHANGE): can0: link becomes readyroot@ok113i:/home/forlinx# ip link set can1 up type can bitrate 500000                                  [ 4086.037967] IPv6: ADDRCONF(NETDEV_CHANGE): can1: link becomes ready
以上设置can0 和 can1 通信速率均为500kbps，这个速率值务必记住，所有接入组网的的can节点都是以这个速率通信。
2. 使用C语言写一个CAN通信的发送接收测试程序，主要验证CAN发送和接收数据是否正常。#include #include #include #include #include #include #include "can_apply.h"#define MASTR_CAN1_ID    0x100#define MASTR_CAN2_ID    0x101#define RX_MSG_NUM          16#define MAX_BUF_LEN       64typedef enum{ CAN_1, CAN_2, CAN_RES}can_type;typedef struct{ int can_id; unsigned char can_dlc; unsigned char data[MAX_BUF_LEN];}can_msg_t;static int bexit = 0;static int can0_sock,can1_sock;can_msg_t can_rx_msg[RX_MSG_NUM];unsigned int can1_id = 0;unsigned int can2_id = 0;void signal_handler(int signo){ printf("signal %d(%s) receivedn", signo, strsignal(signo)); bexit = 1;}int can_send_data(can_type type, unsigned char *buf, int len){ int i, j; int cnt; int sock; int ret = 0; struct can_frame frame; if(type == CAN_1) {       sock = can0_sock;       frame.can_id = can1_id; } else {       sock = can1_sock;       frame.can_id = can2_id; } for(i = 0; i < len; i += 8) {       cnt = len - i;       if(cnt > 8)          frame.can_dlc =  8;       else          frame.can_dlc = cnt;       for(j=0; j